NI TestStand 2019

Author: S | 2025-04-25

Refer to the NI TestStand Help for information about TestStand 2025. You can access the NI TestStand Help in the following ways: Select Help NI TestStand Help in the sequence editor. (Windows 10) Select Start and launch the NI Launcher application, and select TestStand TestStand Documentation TestStand Help.

What is NI TestStand? - NI

Environment Environment shows products that are verified to work for the solution described in this article. This solution might also apply to other similar products or applications. Driver NI-SWITCH NI-DMM NI-SCOPE NI-FGEN For TestStand 2019 and later versions, the main installer doesn't include the IVI Step Types. This article will explore how to install them.Software required: TestStand 2019 (32-bit) until 2022 Q4.Intended audience: This article is intended for TestStand developers that need to develop or support applications that require IVI drivers in a 32-bit environment.Note: For Teststand 2023 Q4 and later, please refer to this kb, Installing IVI Step Types for TestStand 2023 Q4 and Later The IVI Step Types installer can be found in the USB drive that ships with TestStand or in the ISO available in the individual offline installers link at the bottom right of the TestStand download page, as seen in the image below: Once you have downloaded the .iso installer:Mount it by using one of the methods listed here.Open the AdditionalInstallers folder.Open the IVIStepTypes folder located in the AdditionalInstallers folder.Run the autorun or the Install executable.When asked to select the bitness, select 32-bit, and press Next to continue the installation process.NOTE: IVI Steps are not supported in TestStand 64-bit. Reboot the computer to complete the operation. Was this information helpful?

Managing Multiple Versions of TestStand With TestStand Version - NI

How to install this security update. Note Refer to MathScript Module Drops Support for Windows 7 (32- and 64-Bit), Windows Server 2008 R2, and All 32-Bit Windows Operating Systems in 2021 for information about future OS support. Note In 2016 the MathScript Module dropped support for Windows Vista, Windows XP, Windows Server 2003, and installations of Windows 7 without any service packs. The LabVIEW 2019 MathScript Module will not install or run on an unsupported OS. You cannot deploy or distribute applications that use the LabVIEW 2019 MathScript Module to an unsupported OS. Additionally, after installing the LabVIEW 2019 MathScript Module, you cannot use any installers built on this computer with any version of LabVIEW, LabWindows™/CVI™, NI TestStand™, or Measurement Studio on an unsupported OS. For more information about the changes to our OS support for 2016, refer to Why Does My NI ADE Installer Fail on Windows XP/Vista and Windows Server 2003?. Note Support for Windows 32-bit operating systems may require disabling physical address extension (PAE). To learn how this might affect your system and what actions you might need to take, visit ni.com/info and enter the Info Code PAESupport. macOS macOS 10.13 or 10.14 Linux openSUSE LEAP 42.3 openSUSE LEAP 15.0 Red Hat Enterprise Linux Desktop + Workstation 7 Red Hat Enterprise Linux Desktop + Workstation 8 CentOS 7 CentOS 8 Note The LabVIEW 2019 MathScript Module for Linux requires a 64-bit distribution and does not support 32-bit applications. Limitations on Windows (64-bit), macOS, and Linux The MathScript Module on Windows (64-bit), macOS, and Linux does not support the libraries class of MathScript Module functions. Installation Instructions (Windows) NI automates software installation using NI Package Manager. Visit ni.com/info and enter the Info Code NIPMDownload to download NI Package Manager. Refer to the NI Package Manager Manual for more information about installing, removing, and upgrading NI software using NI Package Manager. You can also install LabVIEW and the MathScript Module using the LabVIEW 2019 Platform media. To request additional LabVIEW Platform media, refer to the NI website. Note If you purchased this product with an NI Software Suite or

ExtraPutty in Teststand - NI Community

In the category):LabVIEW 2018 Control Design and Simulation ModuleLabVIEW 2018 Control Design and Simulation Module (64-bit)LabVIEW 2018 MathScript RT ModuleLabVIEW 2018 MathScript RT Module (64-bit)LabVIEW 2018 Statechart ModuleLabVIEW 2018 SoftMotion ModuleLabVIEW 2018 Digital Filter Design ToolkitLabVIEW 2018 Digital Filter Design Toolkit (64-bit)LabVIEW 2018 Robotics ModuleLabVIEW Add-Ons: Deploy:LabVIEW 2018 Real-Time Module (English)LabVIEW 2018 FPGA Module (32-bit) (English)LabVIEW 2018 FPGA Module (64-bit)Click on "Xilinx Compilation Tools - ISE 14.7 for LabVIEW 2018" and choose "Do not install". Then choose "No" when prompted to deselect. See note above.Xilinx Compilation Tools - Vivado 2017.2 for LabVIEW 2018LabVIEW 2018 myRIO ToolkitAutomotive Diagnostic Command Set 15.0LabVIEW Add-Ons: Interface:NoneLabVIEW Add-Ons: Analyze (note that some power analysis functions such as motor harmonic analysis use IP from both NI Sound and Vibration Toolkit and Electrical Power Toolkit):NI Sound and Vibration Toolkit 2018LabVIEW 2018 Advanced Signal Processing ToolkitLabVIEW 2018 Advanced Signal Processing Toolkit (64-bit)Electrical Power Toolkit 2018LabVIEW Modulation Toolkit 18.0LabVIEW 2018 DataFinder ToolkitLabVIEW Add-Ons: Validate:LabVIEW 2018 Unit Test Framework ToolkitLabVIEW 2018 Unit Test Framework Toolkit (64-bit)LabVIEW 2018 VI Analyzer ToolkitLabVIEW 2018 VI Analyzer Toolkit (64-bit)LabVIEW 2018 Desktop Execution Trace Toolkit (32-bit and 64-bit)NI Requirements Gateway 2018LabVIEW Communications:NoneTestStand (if you are performing automated testing on your power converters):NI TestStand 2017 (32-bit)NI TestStand 2017 (64-bit)LabWindows/CVI (tools for C programming):NoneMeasurement Studio (tools for .NET programming):NoneDIAdem (useful for analyzing logged TDMS files such as power converter fault records or real-time test data):DIAdem 2017 SP1 (32-bit) (English)DIAdem 2017 SP1 (64-bit) (English)Stand-Alone Waveform Editors:NoneStand-Alone Vision Software (may be desired if you are using thermal imaging cameras for thermal analysis of your power converters):NoneCircuit Design Suite:Circuit Design Suite 14.1.0 Professional (Includes Multisim and Ultiboard)Note that co-simulation tools for co-simulating your LabVIEW FPGA power electronics control applications along with Multisim power converter circuit models is possible in LabVIEW 2018 (32-bit only), but you must follow the special instructions below to install.Device Drivers:NoneThe device drivers on this media are out of date. So select None and after the installation is done, install NI CompactRIO Device Drivers and NI FlexRIO drivers using these links. You can install these drivers before rebooting, but you must reboot after installing them. Depending on your application, you may want to download and install additional device drivers from ni.com/downloads.NI CompactRIO Device Drivers (download from here)NI FlexRIO (download from here)6. Click Next. Click next again to search for important updates and notifications.7. Choose your installation directories for a drive with sufficient disk space.Note: Installing LabVIEW onto a solid state drive (SSD) is highly recommended as the performance in loading projects and applications is an order of magnitude faster than if installed on a spinning hard drive.8. Click Next again multiple times to review the license agreements and list of products to install. Allow this installer to run.Note: There is no need to disable virus scanning and I do not recommend it for security reasons.9. When the installation completes, select No when prompted if you want to reboot. You can install the latest version of the device drivers before rebooting.For GPIC development, only the NI CompactRIO Device. Refer to the NI TestStand Help for information about TestStand 2025. You can access the NI TestStand Help in the following ways: Select Help NI TestStand Help in the sequence editor. (Windows 10) Select Start and launch the NI Launcher application, and select TestStand TestStand Documentation TestStand Help. Refer to the NI TestStand Help for information about TestStand 2025. You can access the NI TestStand Help in the following ways: Select Help NI TestStand Help in the sequence editor. (Windows 10) Select Start and launch the NI Launcher application, and select TestStand TestStand Documentation TestStand Help.

Install Python for NI TestStand

Had to uninstall an evaluation version before installing the purchased software. With activation, you can download evaluation software and simply activate the fully featured version once purchased. With activation, you also can add features or migrate to higher product levels without reinstalling software. For example, a system deployed on the manufacturing floor contains an NI TestStand Deployment License. If something goes wrong with that system and it needs debugging, you do not need to install additional software. Simply apply a new activation code to enable the NI TestStand Development System to fix the problem.In the past, companies under the Volume License Program (VLP) requested some method of tracking and managing their licenses. Asset management is extremely important in these large organizations, and without the proper tool, the organization could spend more time on tedious tracking tasks and more money on additional licenses they might already own but did not track. With activation, National Instruments provides NI Volume License Manager (VLM) to these companies so they can better manage and track their NI software installation and use. How Do I Activate?NI has made activation quick, easy, and flexible by providing several activation methods. Whatsapp desktop download for mac. It takes only a few minutes of your time and does not require you to formally contact NI directly. When you install the product, the NI Activation Wizard is immediately launched and guides you through the entire activation process. There are six methods available to activate your product. When you activate, the NI

DQMH and TestStand - NI Community

Windows 10 Pro (64-bit) with TestStand 2016 (64-bit) and menu item Configure::Environment. TestStand NOT recognizing specified User's Database path inside the environment.After creating a new environment, the 'StartupCfg.ini' file is included in the files generated within the specified folder. This INI file contains the entry for indicating the location of the Users Database and has as its default value: UserListPath = ""After starting SeqEdit.exe using the /env switch pointed to the associated 'tsenv' file, the path to the Users Database setting was changed in the menu item Configure::Station Options:User Manager tab. The 'StartupCfg.ini' file in the 'environment folder' showed the updated, non-default, path defined via the configuration dialog in TestStand.TestStand was exited and restarted (using the /env switch as indicated previously) and the Login Dialog appeared as usual but the available users were the same as is found launching SeqEdit.exe without the /env switch. Following this, the 'StartupCfg.ini' file in the environment was checked again and it still had the updated path to the users database.TestStand WAS NOT using the environment's specified path for the users database.This use of the 'default' users.ini file in the 'default system cfg' folder when using anenvironment, with it's own specified user's database path, to appears to be a bug in the TestStand software.NOTE: The original 'users.ini' file in the C:\ProgramData>\NI\TS\Cfg was present on the system for the above. As a test, I 'hide' this default user's database file and launched SeqEdit.exe in /env mode, changed the path again, exited TS, then restarted with the /env to find a blank 'users.ini' file was created in the 'C:\ProgramData>\NI\TS\Cfg' path, AND that the Configure Station::User Manager dialog was using the 'default path', still.If this behavior is by design, it stinks. Why copy the 'StartupCfg.ini' to the new environment if it will not be utilized?Thanks in advance.Dave

Integrate TestStand with TortoiseSVN - NI

Framework item on the feature selection screen of the VeriStand installer. Refer to the NI website for a list of compilers that are tested and supported. To compile a LabVIEW VI into a .lvmodel or .lvmodelso file you can load and run, you must complete step 3 of the Installation Instructions to install the VeriStand LabVIEW Model Support item on the feature selection screen of the VeriStand installer. If you use other modeling environments, contact your model vendor for requirements for developing a model and converting it into a compiled model. Supported Operating Systems The LabVIEW Model Interface Toolkit supports the following operating systems: Windows 10/8.11/7 SP12 Windows Embedded Standard 7 SP12 Windows Server 2012 R21 Windows Server 2008 R2 SP12 Note In 2016, the LabVIEW Model Interface Toolkit dropped support for Windows Vista, Windows XP, Windows Server 2003, and installations of Windows 7 without any service packs. The LabVIEW 2020 Model Interface Toolkit will not install or run on an unsupported OS. You cannot deploy or distribute applications that use the LabVIEW 2020 Model Interface Toolkit to an unsupported OS. Additionally, after installing the LabVIEW 2020 Model Interface Toolkit, you cannot use any installers built on this computer with any version of LabVIEW, LabWindows™/CVI™, NI TestStand™, or Measurement Studio on an unsupported OS. For more information about the changes to our OS support for 2020, refer to KB 79UC78LS, Why Does my LabVIEW, LabWindows/CVI, Measurement Studio, or TestStand Built Installer Fail on Windows XP/Vista and Server 2003?. Note Support

NI TestStand 2025 19.0.2

May 2020 This file contains important information about NI System Configuration 20.0, including installation instructions, known issues, and a partial list of bugs fixed. Overview Supported Operating Systems Application Software Support Installation Instructions System Configuration Drops Support for Windows 7 (32- and 64-Bit), Windows Server 2008 R2, and All 32-Bit Windows Operating Systems in 2021 Product Security and Critical Updates Known Issues Bug Fixes Automating the Installation of NI Products Using NI Software with Microsoft Windows 10 Using NI Software with Microsoft Windows 8.1 Legal Information Overview System Configuration 20.0 includes the following products: NI Measurement & Automation Explorer (MAX) 20.0 is a configuration utility that provides access to your NI devices. NI I/O Trace is an application that monitors, records, and displays NI API calls made by applications. NI Device Monitor is a utility for launching applications when a system detects an NI device. System Configuration 20.0 contains an API that can be used to programmatically control various NI devices in a system. Refer to the Application Software Support section of this document for more information on the API. Supported Operating Systems System Configuration 20.0 and components support the following operating systems: Windows 10/8.11/7 SP12 (x86, x64) Windows Embedded Standard 7 SP12 Windows Server 2016 Windows Server 2012 R2 (x64)1,3 Windows Server 2008 R2 SP1 (x64)2,3 NI Real-Time VxWorks NI Real-Time Phar Lap ETS NI Linux® Real-Time Note In 2016 System Configuration dropped support for Windows Vista, Windows XP, Windows Server 2003, and installations of Windows 7 without any service packs. System Configuration 20.0 will not install or run on an unsupported OS. You cannot deploy or distribute applications that use System Configuration 20.0 to an unsupported OS. Additionally, after installing System Configuration 20.0, you cannot use any installers built on this computer with any version of LabVIEW, LabWindows™/CVI™, NI TestStand™, or Measurement Studio on an unsupported OS. For more information about the changes to our OS support, refer to KB 79UC78LS, Why Does my LabVIEW, LabWindows/CVI, Measurement Studio, or TestStand Built Installer Fail on Windows XP/Vista and Server 2003?. 1 NI software installs VC2015 Runtime and .NET 4.6.2. Windows 8.1 and Windows Server 2012 R2 require Microsoft updates to support these items. Refer to Microsoft KB2919442 and KB2919355 for more information about how to install these updates. 2 NI software is signed with a SHA-256 certificate. Windows 7 SP1, Windows Embedded Standard 7 SP1, and Windows Server 2008. Refer to the NI TestStand Help for information about TestStand 2025. You can access the NI TestStand Help in the following ways: Select Help NI TestStand Help in the sequence editor. (Windows 10) Select Start and launch the NI Launcher application, and select TestStand TestStand Documentation TestStand Help. Refer to the NI TestStand Help for information about TestStand 2025. You can access the NI TestStand Help in the following ways: Select Help NI TestStand Help in the sequence editor. (Windows 10) Select Start and launch the NI Launcher application, and select TestStand TestStand Documentation TestStand Help.

TestStand and InstrumentStudio Integration - NI

More information about how to install this security update. Note In 2016 the LabVIEW Real-Time Module dropped support for Windows Vista, Windows XP, Windows Server 2003, and installations of Windows 7 without any service packs. The LabVIEW 2017 Real-Time Module will not install or run on an unsupported OS. You cannot deploy or distribute applications that use the LabVIEW 2017 Real-Time Module to an unsupported OS. Additionally, after installing the LabVIEW 2017 Real-Time Module, you cannot use any installers built on this computer with any version of LabVIEW, LabWindows™/CVI™, NI TestStand™, or Measurement Studio on an unsupported OS. For more information about the changes to our OS support for 2016, refer to KB 79UC78LS, Why Does my LabVIEW, LabWindows/CVI, Measurement Studio, or TestStand Built Installer Fail on Windows XP/Vista and Server 2003?. Note Support for Windows 32-bit operating systems may require disabling physical address extension (PAE). To learn how this might affect your system and what actions you might need to take, visit ni.com/info and enter the Info Code PAESupport. The Real-Time Module installs the following real-time operating systems (RTOSes). Refer to the specific RT target hardware documentation for information about which RTOS your target uses. NI Linux Real-Time Phar Lap ETS VxWorks Note Each RTOS supports only a subset of LabVIEW features. Refer to the Real-Time Module»Real-Time Operating Systems book on the Contents tab of the LabVIEW Help for a list of unsupported LabVIEW features and special considerations for each RTOS. Application Software Support The LabVIEW 2017 Real-Time Module supports the following application software versions, including service packs. Application Software Versions Supported by the LabVIEW Real-Time Module LabVIEW 2017 (32-bit only) Installation Instructions You can install all of your LabVIEW products—including the Real-Time Module—using the LabVIEW 2017 Platform media. To request additional LabVIEW Platform media, refer to the NI website. Note If you purchased this product with an NI Software Suite or NI Product Bundle, use the installation media that shipped with your purchase to install this product. Installing and Using Japanese and Simplified Chinese Languages on an RT Target After you install the Real-Time Module on your development

ActiveX and TestStand - NI Community

We no longer support Internet Explorer v10 and older, or you have compatibility view enabled. Disable Compatibility view, upgrade to a newer version, or use a different browser. Register Login Help Turn on suggestions Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Showing results for Search instead for Did you mean: Topic Options Subscribe to RSS Feed Mark Topic as New Mark Topic as Read Float this Topic for Current User Bookmark Subscribe Mute Printer Friendly Page All Forum Topics Previous Topic Next Topic Previous 1 2 Next Not able to use snippet in my LabVIEW Environment While i am trying to drag and drop code snippet to my LabVIEW BD only the link gets copied in my BD and the same happens in my FP too.Not able to get information from the below post. i need to change any settings in my System? ----------------------------------------------------------------------------------------------------------------Palanivel Thiruvenkadam | பழனிவேல் திருவெங்கடம் LabVIEW™ Champion |Certified LabVIEW™ Architect |Certified TestStand DeveloperKidlin's Law -If you can write the problem down clearly then the matter is half solved.----------------------------------------------------------------------------------------------------------------- udka Active Participant I faced this issue also. Sometimes saved the snippet to local and then drag and drop of snippet works. Thanksuday Author I tried saving the snippet as my local copy, that too is not helping me ----------------------------------------------------------------------------------------------------------------Palanivel Thiruvenkadam | பழனிவேல் திருவெங்கடம் LabVIEW™ Champion |Certified LabVIEW™ Architect |Certified TestStand DeveloperKidlin's Law -If you can write the problem down clearly then the matter is half solved.----------------------------------------------------------------------------------------------------------------- @PalanivelThiruvenkadam wrote:I tried saving the snippet as my local copy, that too is not helping meHmm, strange this should work. So first save the snippet for example into your Documents folder, and then open the folder. After this a drag&drop operation should work.And I agree it is annoying that a drag&drop does not work from browser into a BD. As much as annoying as I cannot attach a VI to a forum post using Firefox. Always need to open Chrome or IE only for this operation, very dumb Hi Blokk,see this thread on problems uploading different file types to the forum.After more than 2 years of complaints I got a solution with help from Lili… Best regards,GerdW using LV2016/2019/2021 on Win10/11+cRIO, TestStand2016/2019 Author Thanks the second option works for me now, just restarted my LabVIEW Application.How to make it work the image snippet from my browser \? ----------------------------------------------------------------------------------------------------------------Palanivel Thiruvenkadam | பழனிவேல் திருவெங்கடம் LabVIEW™ Champion |Certified LabVIEW™ Architect |Certified TestStand DeveloperKidlin's Law -If you can write the problem down clearly then the matter is half solved.----------------------------------------------------------------------------------------------------------------- How to make it work the image snippet from my browser \?Also interested if someone knows a way... Please provide full information:LabVIEW versionBrowser versionOS version @altenbach wrote:Please provide. Refer to the NI TestStand Help for information about TestStand 2025. You can access the NI TestStand Help in the following ways: Select Help NI TestStand Help in the sequence editor. (Windows 10) Select Start and launch the NI Launcher application, and select TestStand TestStand Documentation TestStand Help. Refer to the NI TestStand Help for information about TestStand 2025. You can access the NI TestStand Help in the following ways: Select Help NI TestStand Help in the sequence editor. (Windows 10) Select Start and launch the NI Launcher application, and select TestStand TestStand Documentation TestStand Help.

NI teststand 2025 - Python Integration - NI Community

Used to properly shut down the UI: This user event is generated in the callback for the ExitApplication event and is handled by the event structure in the Handle Events case. Using a LabVIEW user event allows an event structure to handle TestStand events. For more information about LabVIEW user events, refer to the LabVIEW help. Starting the application In the Start Application state, the ApplicationManager calls the start method, which initializes the TestStand engine and starts the user interface. At this point, all visible controls have been connected to manager controls, and TestStand events have been registered to callback VIs. After TestStand has started, the remainder of the user interface execution moves to the Handle Events state. Waiting for Events Most of the user interface execution occurs in the Handle Events state. In this state, the user interface waits for LabVIEW events to occur and processes the using an event structure. Because the controls on the user interface are TestStand UI controls, the events that these controls generate are handled by TestStand manager controls, rather than LabVIEW. This event structure handles two LabVIEW events, both pertaining to shutting down the engine. For example, closing the user interface generates the “Panel Close?” event. The code for this event case is shown below. This event case calls the ApplicationManager Shutdown method, which starts the shutdown process. If the method returns a value of “True,” the TestStand engine has completed shutdown and the shutdown case can execute. Otherwise, the user interface must